Productos

Abrazadera de silla para tubería DI

Número de producto:

DN60-DN300

La función principal de este producto es abrir una tubería de rama o instalar el grifo o el medidor de agua en cualquier parte de la tubería temporalmente después de la finalización de la instalación de toda la tubería y ya en funcionamiento.

El diseño especial es permitido, bienvenido para contactarnos.

Chat ahora

Abrazadera de silla para tubería DI

Número de producto:

DN60-DN300

El diseño especial es permitido, bienvenido para contactarnos.

Chat ahora

No.	Nombre de parte	Material	Estándar
1	Cuerpo	GGG50	EN1563
2	Anillo de goma	EPDM / SBR / NBR	ISO4633
3	Brida de glándula	GGG50	EN1563
4	Pernos y tuercas	Acero al carbono 4.8/8.8, SS, Dacromet	ISO898
5	Capa de acabado	Fusión de fusión epoxi, etc.	BS EN14901

Resumen y características
1	Adecuado para tuberías DI.
2	Presión de trabajo PN10/PN16.
3	Temperatura máxima -10 ° C a+70 ° C.
4	Adecuado para agua potable (aprobado por WRAS), agua reciclada y aguas residuales.
5	La desviación del ángulo total es +/- 3 grados.

Cumplimiento de estándar
Perforación de brida	EN1092-2, EN1092-1, ANSI
Revestimiento	EN30677
Prueba	EN12266-1

Artículo	Especificación (mm)
	∅	F	GRAMO	L	A	L1	H
60~3/4”	60	155	3/4”	80	118	65	M12 × 90
60~1”			1”
60~1 1/4”			1 1/4”
60~1 1/2”			1 1/2”
80~1”	80	175	1”	80	138.5	75	M12 × 90
80~1 1/4”			1 1/4”
80~1 1/2”			1 1/2”
100~1”	100	195	1”	92	165	91	M12 × 90
100~1 1/4”			1 1/4”
100~1 1/2”			1 1/2 ”
100~2”			2”
125~1”	125	220	1”	92	193	104	M12 × 90
125~1 1/4”			1 1/4”
125~1 1/2”			1 1/2”
125~2”			2”
150~1”	150	245	1”	92	209	107	M12 × 100
150~1 1/4”			1 1/4”
150~1 1/2”			1 1/2”
150~2”			2”
175~1”	175	260	1”	92	243.5	129	M12 × 130
175~1 1/4”			1 1/4”
175~1 1/2”			1 1/2”
175~2”			2”
200~1”	200	276	1”	122	276	143	M12 × 140
200~1 1/4”			1 1/4”
200~1 1/2”			1 1/2”
200~2”			2”
250~1”	250	330	1”	122	333	174	M12 × 160
250~1 1/4”			1 1/4”
250~1 1/2”			1 1/2”
250~2”			2”
300~1”	300	380	1”	122	385	200	M12 × 180
300~1 1/4”			1 1/4”
300~1 1/2”			1 1/2”
300~2”			2”

1.This product is specially designed for connecting DI pipes. The connect range is from DN60-DN300. If the customer has special requirements we can design and manufactured. 2.The simplicity and versatility of this product makes the product very easy to install and the entire line can be installed in a running pipeline. It will avoid the shut down the whole pipeline line during saddles installation,which can bring great convenience to customers. 3.Product design and manufacturing in accordance with ISO9001: 2008 system. we use ductile iron material as the main body of product, surface corrosion materials is authenticated by WRAS certification. making it suitable for drinking water. 4.We provide gaskets of EPDM, NBR, and SBR, bolts and nuts of carbon steel and stainless steel, etc., long-term anti-rust protection. For this product we provide excellent protection from transportation, warehousing, anti-corrosion at site.

1.Check the saddle package, if any accessories was lost during transport. 2.Check the diameter and casting marks of the pipe and check the type of model of the saddle, to make sure you use the right products. 3.Thoroughly clean the pipe surface that will use the pipe saddle, brush suitable gasket lubricant for roughened pipes to ensure that the product is well sealed. 4.Loosen the saddle bolt to separate the two part of products. 5.Positioning saddle on the pipe, make sure thread outlet is in the correct position. 6.The bore holes of saddle’s two parts should be aligned to ensure the gasket is parallel to the pipes surface. 7.Tighten the bolt with a wrench as required. The bolt is evenly exchanged with a torque of 15-20 pounds / feet each time.